A 1/4 wave helical antenna with BNC connector, covered entirely with polyolefin rubber heatshrink. The BNCVAR150 has a specially made 1/4λ phosphor bronze helical coil tuned to produce a low SWR and an exceptionally broadband antenna

The BNCVAR+freq can be supplied tuned to any particular frequency from 110MHz to 160MHz simply ask or you can order on line with the code BNCVAR followed with the frequency required eg: BNCVAR151 for 151MHz

Note: This antenna can be supplied as a TNC or N connector or any colour

Note: Also ideal for scanners that are mainly used on High band VHF.

SMAVAR+freq

The SMAVAR+freq can be supplied tuned to any particular frequency from 110MHz to 160MHz simply ask or you can order on line with the code SMAVAR+freq followed with the frequency required eg: SMAVAR151 for 151MHz

The SMAVAR+freq is designed for transceivers where the SMA antenna connector is extended from the case of the transceiver.

A 1/4 wave helical antenna with SMA connector designed especially for exposed SMA connectors on hand held radios and covered entirely with polyolefin rubber heatshrink.

The SMAVAR+freq has a specially made 1/4λ phosphor bronze helical coil tuned to produce an exceptionally broadband antenna.

Note: Also ideal for scanners that are mainly used for 2m band.
Note: This antenna may not fit neatly onto your transceiver

Note: The SMAVAR+freq has a diameter of 12mm at its base and may not fit some radios that have the SMA connector recessed into the radio, if this is the case then the SMAIVAR+freq is the better choice.

SMAIVAR+freq

The SMAIVAR+freq can be supplied tuned to any particular frequency from 110MHz to 160MHz simply ask or you can order on line with the code SMAIVAR+freq followed with the frequency required eg: SMAIVAR151 for 151MHz

The SMAIVAR+freq is designed for transceivers where the SMA antenna connector is recessed into the case of the transceiver.

A 1/4 wave helical antenna with SMA connector designed especially for recessed SMA connectors on hand held radios and covered entirely with polyolefin rubber heatshrink.

The SMAIVAR+freq has a specially made 1/4λ phosphor bronze helical coil tuned to produce an exceptionally broadband antenna.

Note: Also ideal for scanners that are mainly used for 2m band.
Note: The SMAIVAR+freq will fit all hand held radios & scanners that have a SMA connection.

Specifications

Order Code .. RDRMVAR - State freq

Type ........ 1/4 Wave

Pattern ..... Omni-directional

Length ...... 175mm to 200mm

Weight ...... 60grams

Impedance ... 50Ω

Tuning ...... Factory preset

Frequency ... 150MHz~160MHz State freq

Mounting .... 5/16" 26tpi female

RDRMVAR+freq

The RDRMVAR+freq can be supplied tuned to any particular frequency from 110MHz to 160MHz simply ask or you can order on line with the code RDRMVAR+freq followed with the frequency required eg: RDRMVAR151 for 151MHz

The RDRMVAR+freq is the shortest antenna that can be made to suit frequencies from 88MHz to 160MHz and has a bandwidth of up to 4MHz with a SWR <1.5:1 when mounted onto a suitable ground plane area, this represents 2MHz on either side of the desired transmit frequency, the receive frequency is not important. The RDRMVAR is made with weather resistant materials and covered with polyolofin rubber.

Pros - Short antenna - suitable for all mounting positions on vehicles
Cons - Performance reduced due to it being a very short antenna

Recommended Accessories - UL3.6C with BMB or Mag3.6C , Z Bracket is not recommended

Note: You can use a spring SAL or SAO but the antenna will need to be re-tuned on the spring

Stainless steel 1/4 wave antenna can be tuned from 108MHz upward to 500MHz.

This antenna is not pretuned and comes with a cutting chart for customer tuning.

The SW2 works best when mounted onto a bracket that is as close to the surface of the ground plane as possible such as the Mobile One BMB mount. (Z brackets are not recommended with this antenna)

This antenna is available for tuned for frequencies from 108MHz to 160MHz state the tx frequency range required

Pros  - Stainless Steel

Cons  - Not as broadband as the M172-1 (see below)

Recommended Accessories - UL4C with BMB or Mag3.6C. Z Bracket is not recommended
Note: You can use a spring SAL or SAO but the antenna will need to be re-tuned on the spring

Code : SWP - For Tranceivers with SO239 Connection
The SW2 with the UL12C Base cable & Plug as a pack    

Code : SWPBNC - For Scanners or Airband Radios with BNC
The SW2 with the UL12BNC Base cable & Plug as a pack    

The M152-1 can be supplied tuned to any particular frequency from 88MHz to 160MHz simply ask or you can order on line with the code M152-1 replacing the 152 with the frequency you require in MHz

Lightweight fiberglass 1/4 wave antenna suitable for frequencys ranging from 88MHz to 160MHz.

The M152-1 works best when mounted onto a bracket that is as close to the surface of the body of the vehicle as possible such as the Mobile One BMB mount. (Z brackets are not recommended with this antenna)

Pros  - Broadband, Light Duty

Pros  - No need to tune - no SWR meter needed

Recommended Accessories - UL4BNC or UL3.6C with BMB or Mag3.6C . Z Bracket is not recommended
Note: You can use a spring SAL but the antenna will need to be re-tuned on the spring

The M152HD-1 can be supplied tuned to any particular frequency from 118MHz to 160MHz simply ask or you can order on line with the code M152HD-1 replacing the 152 with the frequency you require in MHz

Heavy duty fiberglass 1/4 wave antenna suitable for frequencys ranging from 110MHz to 160MHz.

The M152HD-1 works best when mounted onto a bracket that is as close to the surface of the ground plane as possible such as the BMB mount (Z brackets are not recommended with this antenna)

The M152HD-1 is coated with Black polyolefin and is available in also in White, RED, GREEN, BLUE or YELLOW.

Recommended Accessories - UL3.6C with BMB or Mag3.6C

Pros  - Exceptionally Broadband, Heavy Duty

Pros  - No need to tune - no SWR meter needed

Note: You can use a spring SAL or SAO but the antenna will need to be re-tuned on the spring

The M152-3 can be supplied tuned to any particular frequency from 140MHz to 160MHz simply ask or you can order on line with the code M152-3 replacing the 152 with the frequency you require in MHz

Fiberglass 5/8 wave antenna suitable for vehicle and base applications on a 5/16" fitting
The M152-3 works best when mounted onto a bracket that is as close to the surface of the ground plane as possible such as the BMB mount (Z brackets are not recommended with this antenna)

Pros  - Broadband

Cons  - Long antenna

Recommended Accessories - UL4BNC or UL3.6C with BMB or Mag3.6C. Z Bracket is not recommended
Note: You can NOT use a spring with this antenna.