Air-band Antennas

A 1/4 wave helical antenna with BNC connector, covered entirely with polyolefin rubber heatshrink The BNCVAR124 has a specially made 1/4λ phosphor bronze helical coil tuned to produce an exceptionally broadband antenna for use on the entire Air Band 118MHz to 136MHz. Note: Also ideal for scanners that are mainly used for Air Band reception.

SMAVAR124 for radios where the SMA antenna connector is extended from the case of the radio

SMAIVAR124 for radios where the SMA antenna connector is recessed into the case of the radio

Ground independent fibreglass dipole antenna with 3.6m cable and BNC connector
The Airkit is the most popular air band antenna as it is happy to be mounted almost anywhere with excellent results
The Airkit is available with many different cable lengths, patch leads and frequencies including UHF CB - please ask !

The Airkit is coated with Black polyolefin and is available in also in White, RED, GREEN, BLUE or YELLOW

The Airkit top section is a 1/4 wave 7mm thick broadband antenna that is 515mm long when tuned to the centre of the band ie: 124MHz

The Airkit bottom section is a rubber ducky antenna 260mm long when tuned to the centre of the band ie: 124MHz

Note: When mounting this antenna on a king post , It should be at least 300mm away from the post to get the best results.

Solid fibreglass former with flexible spring top & coated with black polyolefin rubber on a 5/16" fitting
The RDRM124 works best when mounted onto a bracket that is as close to the surface of the ground plane as possible such as the BMS mount (Z brackets are not recommended with this antenna)

Recommended Accessories - UL12BNC or UL12C with BMS or Mag12C

Note: You should not use a spring with this antenna.

Stainless steel 1/4 wave antenna suitable for all air band applications on a 5/16" fitting. The SW2 works best when mounted onto a bracket that is as close to the surface of the ground plane as possible such as the BMS mount. (Z brackets are not recommended with this antenna)

Recommended Accessories - UL12BNC or UL12C with BMS or Mag12C

Note: You can use a spring SAL or SAO but the antenna will need to be re-tuned on the spring.

Stainless steel 1/4 wave antenna suitable for all air band and high band VHF applications tuneable from 108MHz, This antenna is not pretuned and comes with a cutting chart for customer tuning' The SW2 works best when mounted onto a bracket that is as close to the surface of the ground plane as possible such as the BMS mount. (Z brackets are not recommended with this antenna)

Recommended Accessories - UL12BNC or UL12C with BMS or Mag12C

Note: You can use a spring SAL or SAO but the antenna will need to be re-tuned on the spring.

Fibreglass 1/4 wave antenna suitable for all air band applications on a 5/16" fitting. The M124-1 works best when mounted onto a bracket that is as close to the surface of the ground plane as possible such as the BMS mount (Z brackets are not recommended with this antenna)

Recommended Accessories - UL12BNC or UL12C with BMS or Mag12C

Note: You can use a spring SAL or SAO but the antenna will need to be re-tuned on the spring.

Fibreglass 5/8 wave antenna suitable for vehicle and base applications on a 5/16" fitting, The M124-3 works best when mounted onto a bracket that is as close to the surface of the ground plane as possible such as the BMS mount (Z brackets are not recommended with this antenna)

Recommended Accessories - UL12BNC or UL12C with BMS or Mag12C

Note: You Should NOT use a spring with this antenna.

Hollow fibreglass ground independent with with 20mm aluminium anodized tube for mast mounting. This antenna is broadband covering the entire AIR band 118MHz to 136MHz without the need for tuning. The CDB124 is centered on 124MHz and has a bandwidth of 6MHz under 1.6:1 SWR it is therefore important that the desired transmit frequency is taken into consideration. Ideal for scanning the Airwaves

Specifications

1. Order Code ... SAN1090
2. Type ......... Collinear
3. Pattern ...... Omnidirectional
4. Total Length . 950mm or 38
5. Total Weight . 240grams
6. Impedance .... 50Ω
7. Tuning ....... Factory preset
8. Frequency .... 1070MHz ~ 1100MHz
9. Gain ......... 7.0dBi
10. VSWR ......... < 1.5:1 over 30MHz
11. Mounting ..... 1/2UNF Male
12. Cable ........ 1Mtr RG58Cellfoil
13. Connector .... N - Female, SMA etc

SAN1090

The SAN1090 is a fibreglass high gain multi element omnidirectional collinear antenna that is designed for use for ADS-B reception. The SAN1090 has approximately one metre long of 50Ω low loss coax terminated in a FME Female Connector, however the antenna can be supplied with any connector but the size of the connector is to be taken into consideration as it has a 1/2" nut at its base.

Note: The SAN1090 can be supplied with any length coax and with almost any connector PLEASE ASK.
Note: The coax is to be kept as short as possible to get the best performance.